

Gas appliances rarely fail without warning. Strange smells, pilot light issues or inconsistent heating are often early signs. Fixing problems early is usually safer, less disruptive and more cost-effective.
GRAEME MARTIN - Certifying Master Gas Fitter & Plumber
45+ years experience
Hob won't light? Heater cutting out? Planning a gas install?
Gasfitting Services Across Auckland

GAS INSTALLATION AUCKLAND
New gas hobs and cooktops, heaters, gas fires, outdoor BBQ points, renovations and new builds. We check the supply can handle the load, run the pipework, connect and pressure-test, then issue your gas certificate. You'll have a fixed written quote before any work begins, so there are no surprises on the invoice.

GAS HEATER & APPLIANCE SERVICING
A heater that's slow to light, a yellow flame instead of a blue one, or a sooty mark above the unit. These are early warnings. We clean, test and adjust gas heaters, fires and cooktops so they run safely and efficiently through winter. Most manufacturers recommend a service every one to two years.

GAS LEAK DETECTION & REPAIRS
A faint smell near the meter or bottles, a hissing fitting, or a gas bill that has crept up for no reason. We pressure-test the system to confirm whether there's a leak, find it, repair it properly and retest before we leave. The earlier it's found, the safer and simpler the fix. If you can smell gas right now, follow the safety steps below first.

COMMERCIAL GASFITTING AUCKLAND
Commercial kitchens, food production sites, cafes and workshops. When gas goes down, so does the operation. We plan work around your production schedule, keep downtime to a minimum and hand over the compliance documentation your insurer and auditors will ask for. Planned maintenance is available so problems are caught before they stop the line.
Install, replace, convert and certify
Gas Hot Water Systems in Auckland

No hot water this morning, or planning an upgrade? We install and replace continuous flow gas hot water from Rinnai, Rheem and Bosch, sized to the number of showers your household actually runs. Every install is pressure-tested and certified before we leave, and you keep the gas certificate for your records and your insurer.
Moving from LPG bottles to natural gas, or adding gas to a renovation? We check what supply is available, convert or replace the appliances and certify the work. Our gasfitters work across St Johns, Meadowbank, Remuera, Mission Bay, St Heliers, Glendowie, Ellerslie, Mt Wellington, Parnell, Epsom and Howick.
Worth reading: why gas compliance matters for insurance and the complete guide to gas heating and hot water. Planning new hot water? See continuous flow gas hot water or heat pump hot water.
Already have gas at the property? We can add a hob, heater or outdoor BBQ point to the existing line where the supply allows. We check the pipe sizing first, so every appliance gets the pressure it needs.
Every gas job finishes the same way: tested, certified and explained, so you know exactly what was done and what to keep an eye on.
What Does a Gasfitter Cost in Auckland?
No call-out fee. Your first hour on site is $160 + GST, with travel included. After that it's $120 + GST per hour, in 15-minute blocks.
Typical gas jobs
Gas hob installation (you supply the hob): from $400 + GST
Gas storage hot water cylinder replacement: from $2,800 + GST
Continuous flow gas hot water, supplied and installed: from $3,600 + GST
Gas heaters, fires, BBQ points and LPG conversions: fixed written quote after we look
Installation prices include your gas certificate. For installations and conversions, we look first and give you a fixed written quote before any work begins. After-hours rates are published in full on our pricing page.
How it works
1. Tell us what's happening. Book online or call.
2. We assess and give you a clear price.
3. We install, connect and pressure-test.
4. You get your gas certificate.

Gas Fitting Questions We Get Asked
Yes. Gasfitting is restricted work in New Zealand. It has to be done or supervised by a gasfitter registered with the Plumbers, Gasfitters and Drainlayers Board (PGDB). DIY gas work isn't legal, it isn't safe, and it can leave you without insurance cover if something goes wrong. You can check any gasfitter on the PGDB public register.
There's no call-out fee. Your first hour on site is $160 + GST, with travel included. After that it's $120 + GST per hour, in 15-minute blocks. As a guide, a gas hob installation starts from $400 + GST, a gas storage cylinder replacement from $2,800 + GST, and continuous flow gas hot water supplied and installed from $3,600 + GST. For installations and conversions we look first and give you a fixed written quote, with your gas certificate included, before any work begins.
When certifiable gas work is finished, your gasfitter issues a certificate recording what was installed and that it was tested. Depending on the job, that's a Certificate of Compliance or a Gas Safety Certificate. Keep it with your house records, because insurers and buyers often ask for it. We issue the right certificate on every job that needs one.
Turn the gas off at the meter or bottle. Don't use light switches, flames or phones near the smell. Open doors and windows, step outside, then call us on 09 570 2052. If the smell is strong or anyone feels unwell, call 111 first.
Most manufacturers recommend a service every one to two years. Book sooner if the heater is slow to light, the flame burns yellow instead of blue, there's soot around the unit, or it keeps cutting out. A service is far cheaper than a replacement heater, and it keeps the air in your home safe.
Yes, where natural gas is available at your street. We check the supply, convert or replace your appliances so they run correctly on the new gas, and certify the work. If natural gas isn't available, we can tidy up and certify your LPG setup instead.
Yes. We run a gas line to a bayonet fitting on your deck or patio, so you can plug in a BBQ or outdoor heater without swapping bottles. It's tested and certified like any other gas installation, and you'll have a fixed quote before any work begins.
Yes. Calls are taken 24/7 on 09 570 2052. After-hours rates are published in full on our pricing page, so you'll know the cost before we come out.
Fault-finding on Rinnai Infinity and similar units needs the manufacturer's own diagnostic equipment, so it's best handled by Rinnai's service team on 0800 746 624. If your unit is near the end of its life, we'll give you a clear price to replace it.






